Neo Skimmer offers the best oil film removal capability with minimal design.
Principle of oil film removal
The oil film that has passed through the Neo Skimmer is crushed very finely and loses its flotation.
Eventually, it enters the inlet of various filters and is biologically decomposed.
It doesn’t take up space.
The largest product, L size, is only 4 cm wide and 4.5 cm high.
It connects to not inlet, but the outlet.
It don’t need electricity.
Based on Bernoulli’s principle, it uses the correlation between flow velocity and pressure.
It doesn’t trap creatures
Since it is located at the outlet, any creature that enters the skimmer is immediately discharged.
It’s easy to adjust
The ability to remove the film can be adjusted by moving the part up and down and rotating the left and right sides.
Neo reliever has a diameter of 40mm and a thickness of 22mm(M) and 26mm(L)
Neo Flow is a set of inlet and outlet with a transparent, high elasticity and compact design
Even when used without a wing, it lowers the flow velocity, but when equipped with a wing it is completely reduced
Terra Line is a special thread product for securing plants such as epiphytic orchids to driftwood enabling it to secure without melting and breaking in the water. Because it is synthetic fiber, it will not be melt or broken even if it’s used in watery areas. So it is possible to firmly secure plants with less rooting ability and plants that need a lot of time to take roots.
Glass U Tube joint for silicone tubing
20 mm size suitable for rimless aquariums and most standard aquarium rims
Great for use with CO2 injection systems or bubblers
Monitors pH solution in aquarium
Easy-to-read color changing indicator solution included
Recommended for planted aquaria with CO2injection systems
Minimizes the visibility of CO2 equipment in the aquarium
Ensures maximum dissolution of CO2 in aquarium water
Allows for more consistent dosing of CO2
Compatible with 12 mm ID/16 mm OD hoses
Minimizes the visibility of CO2 equipment in the aquarium
Ensures maximum dissolution of CO2 in aquarium water
Allows for more consistent dosing of CO2
Compatible with 16 mm ID/22 mm OD hoses
Content
Why not?? Change it!!
Neo Skimmer offers the best oil film removal capability with minimal design.
Principle of oil film removal
The oil film that has passed through the Neo Skimmer is crushed very finely and loses its flotation.
Eventually, it enters the inlet of various filters and is biologically decomposed.
It doesn't take up space.
The largest product, L size, is only 4 cm wide and 4.5 cm high.
It connects to not inlet, but the outlet.
It don't need electricity.
Based on Bernoulli's principle, it uses the correlation between flow velocity and pressure.
It doesn't trap creatures
Since it is located at the outlet, any creature that enters the skimmer is immediately discharged.
It's easy to adjust
The ability to remove the film can be adjusted by moving the part up and down and rotating the left and right sides.
Aeration is possible.
Aeration is possible when setting high level
Overview
The 20 mm glass U Tube allows you to easily run airline (preferably silicone) for CO2 or for general air supply over the rim of the aquarium without bending or creasing. Made of strong clear glass, which minimizes visibility of tubing.
Compatible with 6 mm (1/4") - Standard Airline Tubing.
Directions
Rinse glassware with warm water. Trim and attach desired tubing (Compatible with 6 mm (1/4") - Standard Airline Tubing).
To attach tubing to glassware, wet the inside of the tubing with water at the attachment point and carefully slide tubing over glass. The use of other lubricants is not advisable as these usually make the tubing slide off of the glassware too easily. To avoid breakage when removing tubing, do not pull tubing off of glassware. Instead, cut tubing carefully along the attachment length to release the glassware.
Install check valve, if desired, (not included) inline with tubing outside of the aquarium
Mount your U Tube over the rim of your aquarium in the desired location
Overview
The pH checker is a glass pH monitor that comes with pH sensitive indicator solution. When submerged in water, this indicator solution changes color according to changes in the pH of the aquarium as a result of CO2 gas. The pH checker makes monitoring CO2 concentrations and pH level in planted aquaria easy.
Suction cup included.
Directions
pH Checker works with any size aquarium. Holding the funnel side of pH Checker upward fill the small bulb with 20 drops of indicator solution. Slowly turn the funnel side down avoiding any spillage of the solution. Insert pH Checker into aquarium funnel side down trapping air in the funnel. Attach the pH Checker in aquarium at the furthest point from any diffuser.
The color of the indicator solution will change yellow to green to blue according to the pH of the water. A more yellow color indicates lower pH / more CO2. A more blue color indicates higher pH / less CO2.
The 13 mm glass Inline Diffuser is a pollen style inline CO2 diffuser that is placed in the outflow line of the filter or aquarium pump to efficiently diffuse CO2gas into the aquarium. This placement of the diffuser avoids the need for a diffuser in the aquarium and significantly reduces the visibility of the CO2injection system in the aquascape. This also allows for more rapid diffusion of CO2 into the system and can allow for more consistent levels and reduce waste of CO2 or overdose of CO2
Compatible with 12 mm ID/16 mm OD hoses. Compatible with 6 mm (1/4") - Standard Airline Tubing. Suction cups included.
Rinse glassware with warm water. Cut filter hose (Compatible with 12 mm ID / 16 mm OD filter hose) to appropriate length so that inline diffuser will hang vertically next to aquarium glass when filter outflow is placed on aquarium. Attach aquarium hose, ensuring that diffuser disc faces “up” toward outflow. Attach suction cups and desired tubing (Compatible with 6 mm (1/4") - Standard Airline Tubing) to the CO2 in line of the diffuser.
Install check valve (not included) inline with 6 mm (1/4") tubing (CO2 in)
To attach tubing and hose to glassware, wet the inside of the tubing or hose with water at the attachment point and carefully slide tubing over glass. The use of other lubricants is not advisable as these usually make the tubing slide off of the glassware too easily. To avoid breakage when removing tubing or hose, do not pull tubing off of glassware. Instead, cut tubing or hose carefully along the attachment length to release the glassware.
Mount your inline diffuser using the suction cup(s). It should be positioned so that it sits vertically on the side or back of the aquarium. When removing or repositioning the diffuser, pull by the suction cup(s) rather than the glass to avoid breakage.
Once securely mounted, turn on filter. Ensure that water passes through diffuser and into aquarium without leaks or bubbles. Turn on CO2. Observe bubble count (bubble counter not included) and adjust CO2 to desired flow rate. Seachem Bubble Counter available for easy monitoring of CO2 flow.
The 17 mm glass Inline Diffuser is a pollen style inline CO2 diffuser that is placed in the outflow line of the filter or aquarium pump to efficiently diffuse CO2gas into the aquarium. This placement of the diffuser avoids the need for a diffuser in the aquarium and significantly reduces the visibility of the CO2injection system in the aquascape. This also allows for more rapid diffusion of CO2 into the system and can allow for more consistent levels and reduce waste of CO2 or overdose of CO2
Compatible with 16 mm ID/22 mm OD hoses. Compatible with 6 mm (1/4") - Standard Airline Tubing. Suction cups included.
Rinse glassware with warm water. Cut filter hose (Compatible with 12 mm ID / 16 mm OD filter hose) to appropriate length so that inline diffuser will hang vertically next to aquarium glass when filter outflow is placed on aquarium. Attach aquarium hose, ensuring that diffuser disc faces “up” toward outflow. Attach suction cups and desired tubing (Compatible with 6 mm (1/4") - Standard Airline Tubing) to the CO2 in line of the diffuser.
Install check valve (not included) inline with 6 mm (1/4") tubing (CO2 in)
To attach tubing and hose to glassware, wet the inside of the tubing or hose with water at the attachment point and carefully slide tubing over glass. The use of other lubricants is not advisable as these usually make the tubing slide off of the glassware too easily. To avoid breakage when removing tubing or hose, do not pull tubing off of glassware. Instead, cut tubing or hose carefully along the attachment length to release the glassware.
Mount your inline diffuser using the suction cup(s). It should be positioned so that it sits vertically on the side or back of the aquarium. When removing or repositioning the diffuser, pull by the suction cup(s) rather than the glass to avoid breakage.
Once securely mounted, turn on filter. Ensure that water passes through diffuser and into aquarium without leaks or bubbles. Turn on CO2. Observe bubble count (bubble counter not included) and adjust CO2 to desired flow rate. Seachem Bubble Counter available for easy monitoring of CO2 flow.
Gradation Sheet is an electrostatic film for adding a beautiful finish touch to the back of Nature Aquarium in a natural way. And by combining it with separately sold Light Screen, the stage effect for the background is enhanced. Due to the nature of an electrostatic film, this product can be used repeatedly.
It is used for the connection between CO2 Regulator and Check Valve. This tube is also good for connecting the joint parts. Do NOT connect it directly to the glass products.
Superge is a detergent removing the algae stuck on the glass items. Pollen Glass and Lily Pipe become clean in a Superge solution after being soaked for a certain period.
Read moreLogin to view price
