Neutral Regulator® adjusts pH to neutral (pH 7.0) from either a low or high pH and maintains it there. It softens water by precipitating calcium and magnesium while removing any chlorine, chloramine, and detoxifying ammonia. The use of Neutral Regulator® makes other conditioning unnecessary. To lower pH below 7.0 use Neutral Regulator® with Acid Regulator™ (or Discus Buffer®). To raise pH above 7.0 use with Alkaline Regulator™. All of these products will enhance and stabilize the freshwater aquarium environment. For further freshwater environment enhancement, use Fresh Trace™ to restore the proper level of trace elements and feed NutriDiet® Tropical Flakes for thriving, healthy freshwater community fish.
Contains phosphate buffers and conditioning agents. Safe for all freshwater fish acclimated to neutral pH.
Directions
Use 5 g (1 level teaspoon) for every 40–80 L (10–20 US gallons) once or twice a month (or as necessary to maintain a pH of 7.0.) Neutral Regulator® may be be initially used daily in cases of high alkalinity until 7.0 is established. It may be added directly to the aquarium at any time. Ideally, it should be used when adding or changing water by dissolving in the replacement water. For precise dosing, use the Seachem Digital Spoon Scale.
Adjusts pH to neutral (pH 7.0) from either a low or high pH
Softens water by precipitating calcium and magnesium
Removes chlorine, chloramine, or ammonia
Water clarifier for marine and freshwater
Clears all types of clouding
Reef and plant safe
Adjusts pH to 5.0—8.0
Designed for use in planted aquariums
Converts carbonate alkalinity (KH) into available CO2
Contains no phosphate
Complete and concentrated conditioner for both fresh and saltwater
Removes chlorine, chloramine
Detoxifies ammonia, nitrite, and nitrate
5X more concentrated than competing products
Adjusts pH to 7.2—8.5
Designed for use in planted aquariums
Increases alkalinity
Contains no phosphate
Creates ideal environment for goldfish
Aids in the prevention of nitrite poisoning
Content
Overview
Neutral Regulator® adjusts pH to neutral (pH 7.0) from either a low or high pH and maintains it there. It softens water by precipitating calcium and magnesium while removing any chlorine, chloramine, and detoxifying ammonia. The use of Neutral Regulator® makes other conditioning unnecessary. To lower pH below 7.0 use Neutral Regulator® with Acid Regulator™ (or Discus Buffer®). To raise pH above 7.0 use with Alkaline Regulator™. All of these products will enhance and stabilize the freshwater aquarium environment. For further freshwater environment enhancement, use Fresh Trace™ to restore the proper level of trace elements and feed NutriDiet® Tropical Flakes for thriving, healthy freshwater community fish.
Contains phosphate buffers and conditioning agents. Safe for all freshwater fish acclimated to neutral pH.
Directions
Use 5 g (1 level teaspoon) for every 40–80 L (10–20 US gallons) once or twice a month (or as necessary to maintain a pH of 7.0.) Neutral Regulator® may be be initially used daily in cases of high alkalinity until 7.0 is established. It may be added directly to the aquarium at any time. Ideally, it should be used when adding or changing water by dissolving in the replacement water. For precise dosing, use the Seachem Digital Spoon Scale.
Overview
Clarity™ is the ultimate clarifier for both fresh and saltwater. It employs an advanced polymeric flocculating agent that is both reef and plant safe. Clarity™ is the only clarifier on the market that does it all! Clarity™ will clear all types of clouding.
Many companies manufacture multiple products to clear up each type of cloudiness and each different environment (e.g. freshwater, marine, reef, etc.). Some companies have developed products that will clear most types of cloudiness, but their application requires two separate bottles of product. Clarity™ contains compounds that will clear all types of cloudiness in all environments.
Clarity™ contains both precipitating and flocculating agents in the same bottle, enabling all types of cloudiness to be removed in one dose.
Upon adding Clarity™ to the water, you will see a cloudy haze begin to form. This is normal and means that Clarity™ is beginning to work. The water is filled with tiny pieces of floating matter that were not visible to the naked eye. Clarity™ makes those pieces of matter begin to clump together. As they clump together they form larger pieces of matter that are now visible, hence the cloudiness. Once this matter has clumped together, it is a simple matter of mechanical filtration to remove the residue. Matter that was once too small to get caught in filter media is now in large enough clumps.
In order for Clarity™ to work effectively, you should have a filter with mechanical filtration (e.g., filter floss) connected to your aquarium.
Directions
Use 1 capful (5 mL) for every 80 L (20 US gallons). In some situations the cloudiness may increase after adding Clarity™, however this is normal and is a sign that Clarity™ is actively working. Rapid clarification will follow (1–2 hours). In the case of chemical or particulate clouding clean filter floss or cartridge after tank clears.
Overview
Acid Buffer™ is a non–phosphate buffer to lower pH and buffer with Alkaline Buffer™. Both buffers are designed for the planted aquarium or for very hard water where phosphate buffers may pose an algae or cloudiness problem. Acid Buffer™ lowers pH and buffers between 6.0 and 8.0 when used with Alkaline Buffer™. As Acid Buffer™ lowers pH it converts carbonate alkalinity (KH) into available CO2.
Directions
To lower pH, use 1/4 teaspoon (2g) for every 80 L (20 US gallons) daily until desired pH is reached (this dose lowers alkalinity by about 0.2 meq/L (0.6 dKH)). Larger doses may be required in very hard (KH) or alkaline waters. For precise dosing, use the Seachem Digital Spoon Scale.
In order to adjust pH gradually, or if water is soft or not well buffered, use Acid Buffer™ with Alkaline Buffer™. When using Alkaline Buffer™ & Acid Buffer™ together to target a specific pH, utilize the suggested ratio chart.
HINT: First determine the amount of Alkaline Buffer™ needed for the volume of water. This should be determined based upon your desired alkalinity (KH). Then, divide by the number in the middle column to obtain the correct amount of Acid Buffer™ required.
This chart is based on use in RO or RO/DI water and ratios may need to be adjusted for use in tap water.
1
1.3
6.5
1
2.0
7.0
1
2.5
7.5
1
4.0
8.0
Overview
Nearly all pet aquatics companies manufacture a product that removes chlorine. None of those, however, can compare in quality, concentration, or effectiveness to Seachem’s flagship product: Prime®. Prime® is the complete and concentrated conditioner for both fresh and saltwater. Prime® removes chlorine, chloramine and detoxifies ammonia, nitrite, and nitrate. It is non-acidic and will not impact pH. A further bonus for the reef hobbyist—Prime® will not over-activate skimmers.
Prime® is up to 5x more concentrated than competing products and is the second most concentrated dechlorinator on the market only after our own aquavitro®alpha™.
Prime® may be used during tank cycling to alleviate ammonia/nitrite toxicity. It contains a binder which renders ammonia, nitrite, and nitrate non-toxic, allowing the biofilter to more efficiently remove them. It will also detoxify any heavy metals found in the tap water at typical concentration levels. Use at start-up and whenever adding or replacing water. When transporting or quarantining fish, use Seachem StressGuard™. When adding new fish, use Stability®. Both are ideal for use with Prime®.
Directions
Use 1 capful (5 mL) for each 200 L (50 US gallons) of new water. For smaller volumes, please note each cap thread is approximately 1 mL. May be added to aquarium directly, but better if added to new water first. If adding directly to aquarium, base dose on aquarium volume. Sulfur odor is normal. For exceptionally high chloramine concentrations, a double dose may be used safely. To detoxify nitrite in an emergency, up to 5 times normal dose may be used. If temperature is > 30 °C (86 °F) and chlorine or ammonia levels are low, use a half dose.
Overview
Alkaline Buffer™ is a non–phosphate buffer to raise pH and alkalinity (KH) and buffer with Acid Buffer™. These buffers are designed for the planted aquarium or for very hard water where phosphate buffers may pose an algae or cloudiness problem. Alkaline Buffer™ raises pH and buffers between 7.2 and 8.5. It is gentle, safe, and enhances the freshwater environment.
Directions
To increase pH, use 1 teaspoon (6 g) for every 80 L (20 US gallons) daily until desired pH is reached (this dose raises alkalinity by about 1 meq/L (2.8 dKH)). For precise dosing, use the Seachem Digital Spoon Scale.
In order to adjust pH gradually, use Alkaline Buffer™ with Acid Buffer™. When using Alkaline Buffer™ & Acid Buffer™ together to target a specific pH, utilize the suggested ratio chart.
HINT: First determine the amount of Alkaline Buffer™ needed for the volume of water. This should be determined based upon your desired alkalinity (KH). Then, divide by the number in the middle column to obtain the correct amount of Acid Buffer™ required.
1
1.3
6.5
1
2.0
7.0
1
2.5
7.5
1
4.0
8.0
Overview
Gold Salt™ is designed to provide the optimal environment for all goldfish species. The use of Gold Salt™ also aids in the prevention of nitrite poisoning. The salt is also well suited for routine aquarium freshwater use. It does not impact pH or provide buffering. For pH control use Gold Buffer™. For dechlorination use Gold Basics™. For further goldfish environment enhancement, use Gold Trace™ to restore the proper level of trace elements and feed NutriDiet® Goldfish Flakes for thriving, healthy goldfish.
Directions
Use 18 g (1 tablespoon) for each 40 L (10 US gallons). Use when setting up an aquarium and when making water changes. To add salt to an established tank, do so gradually. It is best to dissolve the salt in a small amount of freshwater before use. Avoid using salt when replacing evaporated water.
