Shopping Cart

close

No products in the cart.

Return to shop

Shopping Cart

close

No products in the cart.

Return to shop
Back

COVE PVC 45 degree elbow – white 25mm

SKU: 66665576 Category:

Quick Comparison

SettingsCOVE PVC 45 degree elbow - white 25mm removeADA Spring Washer S (for pipes under Φ13mm) removeSEACHEM GLASS IN LINE DIFFUSER 13 mm removeADA MOSS COTTON 200M removeADA SUPERGE removeSEACHEM GLASS BUBBLE COUNTING DIFFUSER - POLLEN 17 mm Disc remove
NameCOVE PVC 45 degree elbow - white 25mm removeADA Spring Washer S (for pipes under Φ13mm) removeSEACHEM GLASS IN LINE DIFFUSER 13 mm removeADA MOSS COTTON 200M removeADA SUPERGE removeSEACHEM GLASS BUBBLE COUNTING DIFFUSER - POLLEN 17 mm Disc remove
ImagePlaceholder
SKU66665576453793402927300011603161545379340603374537934029112000116031561
Rating
Price
Stock

In stock

In stock

In stock

In stock

In stock

In stock

AvailabilityIn stockIn stockIn stockIn stockIn stockIn stock
Add to cart

Read more

Read more

Read more

Read more

Read more

Read more

DescriptionThis is a new type of glass washing brush with a flexible wire. Even New Lily Pipe is easily cleaned. Small brush that fits curved pipe and flexible coil-like wire are equipped.
  • Minimizes the visibility of CO2 equipment in the aquarium
  • Ensures maximum dissolution of CO2 in aquarium water
  • Allows for more consistent dosing of CO2
  • Compatible with 12 mm ID/16 mm OD hoses
Moss Cotton is a special thread to tie and fix moss on driftwood. In a quite dark green color similar to that of Willow moss and it will naturally biodegrade after Willow moss has taken root to the driftwood or rock.Superge is a detergent removing the algae stuck on the glass items. Pollen Glass and Lily Pipe become clean in a Superge solution after being soaked for a certain period.
  • Monitor rate of CO2 injection
  • For aquariums up to 75 L (20 US gallons)
  • Low profile design excellent for minimizing the visibility of the diffuser
  • Simple and easy to use
Content
The 13 mm glass Inline Diffuser is a pollen style inline CO2 diffuser that is placed in the outflow line of the filter or aquarium pump to efficiently diffuse CO2gas into the aquarium. This placement of the diffuser avoids the need for a diffuser in the aquarium and significantly reduces the visibility of the CO2injection system in the aquascape. This also allows for more rapid diffusion of CO2 into the system and can allow for more consistent levels and reduce waste of CO2 or overdose of CO2 Compatible with 12 mm ID/16 mm OD hoses. Compatible with 6 mm (1/4") - Standard Airline Tubing. Suction cups included.
 
Rinse glassware with warm water. Cut filter hose (Compatible with 12 mm ID / 16 mm OD filter hose) to appropriate length so that inline diffuser will hang vertically next to aquarium glass when filter outflow is placed on aquarium. Attach aquarium hose, ensuring that diffuser disc faces “up” toward outflow. Attach suction cups and desired tubing (Compatible with 6 mm (1/4") - Standard Airline Tubing) to the CO2 in line of the diffuser. Install check valve (not included) inline with 6 mm (1/4") tubing (CO2 in)   To attach tubing and hose to glassware, wet the inside of the tubing or hose with water at the attachment point and carefully slide tubing over glass. The use of other lubricants is not advisable as these usually make the tubing slide off of the glassware too easily. To avoid breakage when removing tubing or hose, do not pull tubing off of glassware. Instead, cut tubing or hose carefully along the attachment length to release the glassware. Mount your inline diffuser using the suction cup(s). It should be positioned so that it sits vertically on the side or back of the aquarium. When removing or repositioning the diffuser, pull by the suction cup(s) rather than the glass to avoid breakage. Once securely mounted, turn on filter. Ensure that water passes through diffuser and into aquarium without leaks or bubbles. Turn on CO2. Observe bubble count (bubble counter not included) and adjust CO2 to desired flow rate. Seachem Bubble Counter available for easy monitoring of CO2 flow.

Overview

The Bubble Counting Diffuser is a pollen style CO2 diffuser that connects to CO2 injection systems to easily disperse CO2 gas into the planted aquarium. The built-in bubble counter allows for easy monitoring of the rate of CO2 injection. The inclusion of a bubble counter in the diffuser makes the use of a bubble counter on the CO2 tank or in-line unnecessary. The Bubble Counting Diffuser has a 17 mm disc. Compatible with 6 mm (1/4") - Standard Airline Tubing. Suction cup included.

Directions

Rinse glassware with warm water. Attach suction cup and desired tubing (Compatible with 6 mm (1/4") - Standard Airline Tubing) to the diffuser. To attach tubing to glassware, wet the inside of the tubing with water at the attachment point and carefully slide tubing over glass. The use of other lubricants is not advisable as these usually make the tubing slide off of the glassware too easily. To avoid breakage when removing tubing, do not pull tubing off of glassware. Instead, cut tubing carefully along the attachment length to release the glassware. Mount your diffuser using the suction cup(s). It should be positioned low in the aquarium. When removing or repositioning the diffuser, pull by the suction cup(s) rather than the glass to avoid breakage. Install check valve (not included) inline with tubing outside of the aquarium Once securely mounted, turn on CO2. Observe bubble count and adjust CO2 to desired flow rate.
Weight
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Select the fields to be shown. Others will be hidden. Drag and drop to rearrange the order.
  • Image
  • SKU
  • Rating
  • Price
  • Stock
  • Availability
  • Add to cart
  • Description
  • Content
  • Weight
  • Dimensions
  • Additional information
  • Attributes
  • Custom attributes
  • Custom fields
Click outside to hide the comparison bar
Compare